Now Sanyo has just released the PLV-Z3 , which carries on the tradition of delivering continued improvements built around the x engine. The Z3 incorporates a number of refinements over the Z2, including better contrast, deeper black levels, lower fan noise, a wider array of inputs, and a unique feature than enables users to clear dust particles from the LCD panels.
Native Resolution: x Display technology: 3 0. Lamp life: unspecified Weight: 9. There are a variety of precalibrated video settings as well as four user programmable settings. For optimum video quality, brightness will typically measure no more than about to lumens.
As with all projectors rated at ANSI lumens or less, it is intended to be used in a dark viewing space for best results. Manual zoom and focus. Like the Z2, the Z3 offers a manual zoom and focus lens with a 1.
A " diagonal image is attained from a throw distance between 10 to 13 feet. Horizontal and vertical lens shift. The Z3 offers horizontal and vertical lens shift for ease of installation. The lens shift range is extensive. At its neutral position the centerline of the lens strikes the center of the projected image.
That lets you position the entire projected image either to the right or to the left of the centerline of the lens. Two notes are warranted. First, you cannot achieve both extremes of horizontal and vertical shift simultaneously. As you move the lens toward the ends of the vertical shift range your ability to move sideways is increasingly restricted. Second, you should avoid the extreme ends of the lens shift range whenever possible since the lens is not as optically efficient in those positions.
Six video inputs. Furthermore a PC input pin VGA , and a second 3-RCA analog component video have been added to the basic configuration offered on the earlier Z2 which included just one component input. As with the Z2, there is one S-video and one composite video input, both of which should be used only for VCRs, video game boxes, laser disc players, and any sources for which component outputs are not available.
User maintenance of LCD panels. One problem that can occur on any projector that does not have a sealed light engine is that dust particles can settle on the LCD panels. When a dust particle lands on and sticks to an LCD panel, it will produce a small, fuzzy spot on the projected image.
Sanyo has come up with a novel solution to this problem on the Z3. Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.
Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. Hot air is exhausted from the exhaust vent. When using or installing the projector, the following precautions should be taken.
This area will become hot while the projector is being used. The materials put on the cabinet will not only get damaged but also cause fire hazard by heat. Cooling fans are provided to cool down the projector. This projector monitors internal temperature and control the running speed of the cooling fans. Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it. This is a safety feature to be sure that the plug will fit into the power outlet.
Do not try to defeat this safety feature. Should you be unable to. This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.
If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug i.
Fuse covers are available from the Parts Department indicated in your User Instructions. If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted. See Over. As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:. The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Do not put heat-sensitive objects near this side. Connect computer output, or RGB Scart pin video output to this connector. Flashes red until the projector gets ready to be turned on.
It lights red when the projector is in the stand-by mode. It remains green while the projector is under operation. When the front cover is closed it lights orange. Lights red when the projector detects abnormal condition. This also flashes red when the internal temperature of the projector exceeds the operating range.
Selects an item or adjusts value in the On-Screen Menu. These are also used to pan the image in the Digital zoom mode. Executes the item selected. When selecting main menu, all the items will be reset. When selecting sub-menu, the selected item will be reset. This button works when selecting Image level adjustment, Computer adjustment Manual , Keystone and Digital zoom function.
Goes back to the previous screen. When there is no previous screen to go back, displaying screen will disappear. Executes the item selected, or to expand or compress image in the Digital zoom mode. You can directly adjust an item. Point the remote control toward the projector Infrared Remote Receiver whenever pressing any button. Maximum operating range for the remote control is about This projector is designed to project on a flat projection surface and can be focused from 3. Computer Monitor Manuals.
Convection Oven Manuals. Cooktop Manuals. Cordless Drill Manuals. Cordless Telephone Manuals. CRT Television Manuals. Digital Camera Manuals. Digital Photo Frame Manuals.
Digital Photo Keychain Manuals. DVD Player Manuals. DVD Recorder Manuals. DVR Manuals. Fax Machine Manuals. Page 5: Safety Instructions Safety Instructions All the safety and operating instructions should be read before This projector should be operated only from the type of power the product is operated.
If you are not sure of the type of power supplied, consult your authorized dealer or Read all of the instructions given here and retain them for later local power company. Improper Installation may reduce ensure reliable operation of the product and to protect it from the lamp lifetime and cause a fire hazard. Do not put heat-sensitive objects near this side. Air Intake Vent The two arrows show air flow.
These Flashes red until the projector gets ready to be turned on. These are also used to pan the image in the Digital zoom mode. Maximum operating range for the remote control is about Page Installation Installation Positioning the Projector This projector is designed to project on a flat projection surface and can be focused from 3.
Refer to the figure and the table below for the screen size and the distance between the projector and the screen. This projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system. Page Moving The Lens Installation Moving the Lens The projection lens can be moved up, down, left, and right with the manual lens shift function.
This function makes it easy to provide a projected image where you want. NOTE When connecting the cable, the power cords of both the projector and the external equipment should be disconnected Connect the projector's AC power cord into an AC outlet and open the front cover. Focus Ring The Keystone dialog box appears.
0コメント