Page 21 apply the brakes on the pushchair before removing the car seat. Pull the lever located on the back of the car seat upwards and hold in the fully pulled out position. Lift the car seat clear of the pushchair. Pull the locks on the sides of the frame outwards and hold. This product is designed for outdoor use only. Take care when fitting or adjusting the raincover as undue force may damage the raincover. Page Removing The Fabric Cover removing the fabriC Cover Slide the ends of the armrest covers towards the bumper bar, then pull away from the armrest to release the attachment studs.
Repeat the same process to remove the rear attachment studs from the armrests. Unfasten the press studs at the bottom of the wings of the backrest.
Page 25 unfasten one side of the harness by removing the screw as shown in the diagram, you will need to hold on the other side of the frame with your fingers. Unfasten the two press studs holding the seat fabric to the frame. If the harness is damaged, we recommend that a new one is fitted.
Page 28 Pliko Pramette fiuki www. Print page 1 Print document 28 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! There are mesh ventilation panels on the sides of thecover. These are essential to aid the flow of cool air around your baby. Do not let yourpushchair drop.
Carry it up stairs whenever possible. Do not use any replacement parts or accessoriese. The use of non-approved replacement parts or accessories may damageor make your pushchair unsafe. Adjustments and locks should be free and easy to operate. Always allow the fabric to dry naturally awayfrom direct heat. Excessiveweight could damage the basket or impede the safe operation of the pushchair.
We recommend that this is used in conjunction with the appropriate sunprotection cream and clothing. Never attempt to use thepushchair with the covers fittedas the locks will not engage. Release the finger catcheslocated under both of thehandles by pulling themupwards. Lift the pushchair upwards andthe frame will automaticallystart to open.
You may need to press downlightly on the seat to ensurethe safety locks have engaged. There are two safety locks, oneon each side of the pushchair. Warning: Ensure that alllocking devices are engagedbefore use. Push the wheel housing ontothe end of the leg until it locksinto position. Always check that thewheels are correctly fitted byattempting to pull them offagain. Attaching the back wheels:Slot the rear wheels onto theback legs of the pushchair.
Ensure that the brake peddleson the wheels are facing outfrom the back of the pushchair. Push the wheels down as far asthey will go. Check that the pins in thepushchairs legs are protrudingthrough the wheel housings. Check the wheels are correctlyfitted by trying to pull them offagain.
Align the end of the insertwith the moulding on the backframe 2. Slide the insert into themoulding 3. Ensure the inset is fullyinserted into the moulding 4. Fitting the bumper bar:Slide the ends of the bumperbar into the holes in the endsof the armrests.
Push the bumper bar inwardsuntil it clicks into place. Push the two catches on theunderside of the armrestinwards and slide the bumperbar fully in. To extend the bumperbar: Push the catches on theunderside of the armrestsinwards and slide the bumperbar outwards until it locks inplace. To remover the bumperbar: Push the catches underthe armrests inwards and slidethe bumper bar out of thearmrests.
When removing the bumperbar, insert the plugs providedto close the armrests of thechassis. ABCThe two front webbing loopsfit over the hooks on the fontlegs of the pushchair. The hooks are situated justbelow the frame locks oneither side of the frame. We recommend that you donot exceed a load of 3kg in thebasket. Excessive weight coulddamaged the basket. Push the top of the cup holderdownwards until it locks overthe lug.
Check that the cup holderis correctly attached byattempting to pull it of again. Warning: It is dangerous toplace hot drinks in the cupholder. Never hang additionalitems on the cup holder. Once thehandle has been adjusted it willautomatically lock into place. To shorten the handle:Press the bottom of the buttonin and push the grip away fromyou.
To lower the backrest:Pull the backrest adjustmenthandle upwards and lower thebackrest into the position yourequire. Release the handle andmove the backrest upwards ordownwards until it locks intoposition. ATo raise the backrest:Grip the middle of the backrestand lift upwards until it locks inthe position you require. Note: The leg rest must bein the most vertical down position when the pushchair isbeing used by a child that cansit unaided and the backrest isin an upright position.
To adjust the leg rest, pullthe locks on both sides ofthe leg rest in the directionof the arrows in the diagram. Now either lift or lower theleg rest whilst releasing thecatches, the leg rest will lockautomatically into position. Fixed mode:Push the catches between thefront wheels upwards. The wheels will now be fixedand will not swivel. Swivel mode:Push the catches between thefront wheels downwards. Check the brakes arecorrectly engaged by rockingthe pushchair backwards andforwards.
Warning: Always engage thebrakes when you leave or let goof the pushchair for whateverreason. The maximum weight for achild on the ride-on plate is 20kg up to a maximum age of 4years approximately. Before using the ride-on platethe hood must be removedand the backrest raised to thehighest position.
Do not attempt to use theride-on plate with the backrestlowered. Fasten the press studs on theside flaps of the hood onto theinsides of the armrests. Fasten the press studs on theback of the hood onto thestuds on the seats backrest.
Push the tabs on the sides ofthe hood inwards until they arefree of the armrests. Thanks Kirsty x. Take the hood off firstly by just pulling it and up bottom the fasterner things at the back. Then unzip the zip at the top, lay pushchair to its flatest setting and pull the cover over to the other side where it will zip on. Then attach the hood the other way round and fasten down to poppers at back.
Hope that makes sense. Hi - thanks so much for your comment. That does make sense, and we've done that, but it doesn't seem very comfy and flat. Did you have a mattress or liner in yours? Thanks for your help. PS - thanks for the advice about calling them which I can do on Monday and also downloading the instructions.
0コメント